The ASM Lab interface
When a model is open, the ASM Lab window has these areas:
- Menus: File, Edit, Mine and View.
- Ribbon: the tabs Home, Design, Duct and Network, each with groups of buttons.
- Top bar: undo and redo, display modes, the 3D and 2D stope solvers, Downloads, Help, Report bug and Settings.
- Left side bar: Outliner, Drawing pen, Colour and Clip.
- 3D view: the mine, with the view tools down its left edge.
- Right side bar: Inspect, Draw, Network, Solve, Thermal, ASM Assistant and Script.
- Solver log and status bar: at the bottom of the window.
Screenshot 2: The whole ASM Lab window with a sample mine open, numbered 1 to 7 to match the list above.
The ribbon¶
The ribbon holds the commands you use most, grouped by what they do. The Home tab is where you draw, edit and solve. This chapter introduces the ribbon; each button is described where it is used in the chapters that follow.
| Tab | Groups and what they hold |
|---|---|
| Home | Create (Draw tunnel, Curved tunnel, Add shaft, Place fan, Add regulator, Add wall, Refuge bay, Add cooler); Edit (Duplicate, Merge nodes, Delete, Add node, Remove node, Fillet, Extend); Simulate (Check, Fan curves, Report, Fire, Air use, Charts, Library); Solve; Navigate; Display (Colour by, Label by). |
| Design | Create: Split (cut an airway at a point), Add stope, Add door / airlock. |
| Duct | Auxiliary ventilation: ducts, duct fans, size changes and evasés, with the duct's own 3D and 2D views. |
| Network | Boundaries (Intake, Exhaust), fans (Main fan, Booster, Auxiliary), topology, the network report and exports. |
Note: Hide ribbon, at the right end of the ribbon, gives the 3D view more room; click a tab to bring the ribbon back.
Screenshot 3: The ribbon's Home tab, with the Create, Edit, Simulate, Solve, Navigate and Display groups labelled.
Task: Show and hide the ribbon
- Click Hide ribbon at the right end of the ribbon. The ribbon closes and the 3D view grows.
- Click the Home tab to open the ribbon again.
The left side bar¶
| Panel | What it is for |
|---|---|
| Outliner | Everything in the project: files, block models and collections (levels). Show, hide, rename, lock or delete them, and choose which collection new drawing goes into. |
| Drawing pen | Drawing settings, such as the working elevation new points are drawn at. |
| Colour | Colours for drawings, layers and block models. |
| Clip | Six cutting planes to slice into the model, for looking inside a level or an orebody. |
Screenshot 4: The left side bar with the Outliner open, showing a collection and a block model.
The right side bar¶
| Panel | What it is for |
|---|---|
| Inspect | The properties of what you selected: an airway's size, shape, friction factor and device, a node's position and boundary, and their results after a solve. |
| Draw | Drawing by typing coordinates, and other drawing dialogues. |
| Network | Boundaries and the network checks (loose ends, gaps, disconnected parts). |
| Solve | Solver settings and the latest solve. |
| Thermal | Heat sources and thermal settings for the selected airway or the whole model. |
| ASM Assistant | The chat assistant that can draw, solve and explain the model. |
| Script | The script editor and the list of script functions. |
Screenshot 5: The right side bar with the Inspect panel showing a selected airway and its simulation results.
The 3D view¶
The 3D view shows the model. The tools down its left edge fit everything in the view, reset it, and switch the grid, labels, flow arrows and flow animation.
| Key | View |
|---|---|
| 7 | Top |
| 1 | Front |
| 3 | Right |
| 0 | Isometric |
| . | Frame everything |
| 5 | Perspective or orthographic |
Solver log and status bar¶
The status bar at the bottom says what ASM Lab is doing and which collection you are drawing in. The solver log above it reports each solve: whether it converged, and any warnings. Click Show to open the full log.
Screenshot 6: The bottom of the window after a solve: the status bar and the solver log showing Converged.